Use your 3D Printer with a pen to write letters, birthday cards etc
Try the new (still free) version https://3dwriter.io
I couldn't find any small programs that i could use to write letters using my 3D Printer as a plotter so i wrote one. After mucking about with different fonts i found a fontset called the Hershey fonts. These are the only fonts used in this application since they are primarily stroke based fonts rather than outline fonts that every other program i tried had.
Video demo over on youtube https://youtu.be/yK_YGwMRR40
Windows executable is in 3DWriter/bin/Release/3DWriter.exe
Note: Windows10 users may get a security warning, this is normal because i do not sign my applications, click "more info" then "run anyay".
Feel free to check and compile your own :)
There are 3 main columns.
- Text entry
- Preview
- GCode settings
Once you have selected the font from the toolstrip at the top, you can click right next to it on the "Preview" button to see a rendered character set of the font. There is a check button beside that "Simple fonts" which will alternate between the full set of fonts and a simple list. Fonts in other languages will most likely not map to the english character set. Appologies, i only know english.
Type some text in to the Text input. Choose your scale (0.2 is pretty close to handwriting) then click the Preview button to see your text rendered in the preview window.
There are options for scaling up the preview render to make it easier to see what it might look like.
If your GCode settings are complete, just click "Generate GCode" and save the file for your printer.
Pay close attention here
Bed X/Bed Y - Set the size of your printers bed here.
Offset X/Offset Y - My pen is strapped to the side of my extruder so there is an offset.
Pen up/Pen down - This is the height of the extruder/pen head from your build plate. Test this manually on your printer to get these.
Travel / Draw speed - The speed at which the printer will move at. Slower is better.
Line Spacing - The gap between the lines measured in 'units'.
Letter Spacing - The gap between the letters measured in 'units'. Letters already have individual spacing but sometimes more is required.
Home X/Y/Z - Before and after the printer does the writing you probably want to home all your axis. Untick those you don't.
Dry run - Doesn't put the pen down, ever. This is so you can put your paper/card in place and see if it will go where you want it.
Preview magnification makes no difference to the GCode.
The GCode output is higher resolution than the preview window.
The fonts are described in multiple x/y points as integers. Each font has a height around 37. This isn't mm or pixels, it's just what was used to describe the strokes so i call them units. This height is multiplied by the scale to render the fonts. Line and letter spacing is also multiplied by scale so the end result is proportional.
At first i just used a rubber band to hold the pen on but it wiggled around too much so i printed a custom holder that attached firmly to my extruder. Then i printed mating piece and glued it to my pen (4 colour Bic pen).
I made it so when the pen tip is retracted it is higher than my nozzle so i can keep the pen there all the time.
Using a program like Pronterface you can manually move your extruder around to find the correct height for pen up & down, also the X and Y offset so you don't write off the edge of the page.
I equipped my 3D Printer with a cheap 1W UV laser from ebay which work quite well on a variety of materials. I was using Marlin firmware but found there is no support for controlling a laser other than to connect the laser to the cooling fan and use M106/M107 to turn the laser on and off.
Repetier firmware has full laser support so after a bit of mucking about i managed to get it loaded on my GT2560 controller.
Since my printer has only 1 extruder, i decided to use the mosfet output normally used for a second extruder as a 12v power source for my laser. Repetier has a great online configuration tool for setting things like which output to use for laser control.It made this process quite simple.
I used a LM7805 to regulate the 12v supply to 5v that the laser uses. I also connected a simple switch on the laser so i can be sure it's only going to work when i want it too :)
REPETIER USERS... Please remove the laser on/off commands in 3DWriter. The commands required to activate the laser are put in to the GCode file automatically.
MARLIN USERS... You don't have support for the laser GCode's so you need to specify your commands for laser ON and OFF in the program. If you haven't already connected a laser, you can add a switch to the wires going to your part cooling fan so you can switch between cooling or laser. If you do this, your commands will be... Laser ON: M106 Laser Off: M107
ALL USERS... Your cheap sub $25 1W laser from ebay will likely require 5v. Use an appropriate power supply for it, such as an LM7805 which are cheap and very very simple to wire in.
FOCUS... All lasers need to be focused, i found that mine is 68mm from the build plate but that's because of where i mounted my laser. This will be different for ALL users. I suggest using thick cardboard on your buildplate so you don't damage it. Make some simple/quick text, load it up in repetier host or pronterface etc, print it, raise your z-height, repeat until you get good results.
The only 3D Printer i own is a RepRap i3 clone and i can confirm it has been tested and works well on that style of printer. I know from other software made for the ultimaker that sometimes the Z move is the wrong direction, i would advise that you simulate the gcode files prior to printing just to be sure you know what is going to happen. And as always when trying new software with your 3D Printer, keep one hand on the off switch :)
I don't claim to be the worlds best programmer, nor am i a self professed 3D Printer expert but i have many years of experience with both and i'm pretty confident that this software works.
I have included the C# 2015 project that you can compile yourself along with a binary build for MS Windows (see 3DWriter/bin/Release).
I would love to hear your feedback :)
Some users have described a blocky / 8-bit look on some printers, comma's found in gcode file instead of periods (for decimal numbers). language localization issue, fixed.
Added a more reliable method of update checking.
Added real line height to status bar.
Updated path seperators with Path.DirectorySeparatorChar.
Work has begun on the font editor which is included in this version but disabled in the menu since it's no where near complete.
Fixed GCode offset issue with Y axis.
Fixed incorrect index of character array causing erroneous moves.
Added version checking.
Changed ui font scale to font size in mm.
(sorry for the multiple commits, has been a long day)
