asksinpp with Infrared-Library

[thunder1902]

Hi!
I have a question:
If i use the asksinpp-Library with an infrared-Library together, the homematic-communication freezes.
Can you give me a tip, how i can use the asksinpp-Library with an infrared-library?
Thank you very much!
Here is my code:

//- -----------------------------------------------------------------------------------------------------------------------
// AskSin++
// 2016-10-31 papa Creative Commons - http://creativecommons.org/licenses/by-nc-sa/3.0/de/
//- -----------------------------------------------------------------------------------------------------------------------

// define this to read the device id, serial and device type from bootloader section
// #define USE_OTA_BOOTLOADER

// number of relays by defining the device
#define HM_LC_SW1_SM 0x00,0x02
#define HM_LC_SW2_SM 0x00,0x0a
#define HM_LC_SW4_SM 0x00,0x03

#define CFG_LOWACTIVE_BYTE 0x00
#define CFG_LOWACTIVE_ON   0x01
#define CFG_LOWACTIVE_OFF  0x00

#define DEVICE_CONFIG CFG_LOWACTIVE_OFF

// #define HM_SENSOR_RELAY

#define EI_NOTEXTERNAL
#include <EnableInterrupt.h>
#include <AskSinPP.h>
#include <LowPower.h>

#include <Switch.h>

//----IR-------------
  #include "IRRemoteControl.h"
  unsigned int ir_off[] = {3608, 9000, 8932, 4292, 660, 460, 656, 1548, 656, 488, 628, 464, 656, 460, 656, 1548, 656, 464, 656, 460, 656, 1548, 660, 460, 656, 1548, 660, 1548, 656, 1552, 656, 460, 656, 1548, 660, 1548, 656, 1552, 656, 460, 656, 460, 656, 464, 652, 1552, 656, 460, 656, 464, 656, 460, 656, 460, 656, 1548, 660, 1548, 656, 1548, 660, 460, 656, 1548, 660, 1548, 656, 1548, 660};
      unsigned int ir_night[] = {};
 //     unsigned int ir_on[] = {208, 3388, 1780, 48208, 8928, 4296, 656, 460, 656, 1552, 656, 460, 656, 460, 656, 460, 660, 1548, 656, 460, 656, 460, 660, 1548, 656, 484, 632, 1552, 656};
//----IR-------------

// we use a Pro Mini
// Arduino pin for the LED
// D4 == PIN 4 on Pro Mini
#define LED_PIN 4
// Arduino pin for the config button
// B0 == PIN 8 on Pro Mini
#define CONFIG_BUTTON_PIN 8

#ifdef HM_SENSOR_RELAY
  // relay pins for the HMSensor Relay Board
  #define RELAY1_PIN 17
  #define RELAY2_PIN 16
  #define RELAY3_PIN 15
  #define RELAY4_PIN 14
  #define BUTTON1_PIN 6
  #define BUTTON2_PIN 3
  #define BUTTON3_PIN 1

  #define BUTTON4_PIN 18
#else
  // relay output pins compatible to the HM_Relay project
  #define RELAY1_PIN 5
  #define RELAY2_PIN 6
  #define RELAY3_PIN 7
  #define RELAY4_PIN 17
#endif

// number of available peers per channel
#define PEERS_PER_CHANNEL 8


// all library classes are placed in the namespace 'as'
using namespace as;

// define all device properties
const struct DeviceInfo PROGMEM devinfo = {
    {0x12,0x34,0x16},       // Device ID
    "flurlicht",           // Device Serial
    {HM_LC_SW4_SM},         // Device Model
    0x16,                   // Firmware Version
    as::DeviceType::Switch, // Device Type
    {0x01,0x00}             // Info Bytes
};

/**
 * Configure the used hardware
 */
typedef AvrSPI<10,11,12,13> RadioSPI;
typedef AskSin<StatusLed<LED_PIN>,NoBattery,Radio<RadioSPI,2> > Hal;

//CLASS--------------------------
class IRChannel : public SwitchChannel<Hal, PEERS_PER_CHANNEL, List0> {
  public:
    IRChannel () {};
    virtual ~IRChannel () {};
   virtual void switchState(__attribute__((unused)) uint8_t oldstate, uint8_t newstate, uint32_t delay) {

      IRSend irsend;
      int khz = 38; // 38kHz carrier frequency   
      unsigned int ir_on[] = {208, 3388, 1780, 48208, 8928, 4296, 656, 460, 656, 1552, 656, 460, 656, 460, 656, 460, 660, 1548, 656, 460, 656, 460, 660, 1548, 656, 484, 632, 1552, 656};         
      if (newstate == AS_CM_JT_ON) {
        // put your ir send code here
        irsend.sendRaw(ir_on,sizeof(ir_on) / sizeof(ir_on[0]),khz,true);
      }
      SwitchChannel<Hal, PEERS_PER_CHANNEL, List0>::switchState(oldstate, newstate, delay);
    }
};
//----------------------END CLASS


// setup the device with channel type and number of channels
//typedef MultiChannelDevice<Hal,SwitchChannel<Hal,PEERS_PER_CHANNEL,List0>,4> SwitchType;
typedef MultiChannelDevice<Hal, IRChannel, 1> SwitchType;

Hal hal;
SwitchType sdev(devinfo,0x20);
#ifdef HM_SENSOR_RELAY
ConfigButton<SwitchType> cfgBtn(sdev);
InternalButton<SwitchType> btn1(sdev,1);
InternalButton<SwitchType> btn2(sdev,2);
InternalButton<SwitchType> btn3(sdev,3);
InternalButton<SwitchType> btn4(sdev,4);
#else
ConfigToggleButton<SwitchType> cfgBtn(sdev);
#endif


// if A0 and A1 connected
// we use LOW for ON and HIGH for OFF
bool checkLowActive () {
  pinMode(14,OUTPUT); // A0
  pinMode(15,INPUT_PULLUP);  // A1
  digitalWrite(15,HIGH);
  digitalWrite(14,LOW);
  bool result = digitalRead(15) == LOW;
  digitalWrite(14,HIGH);
  return result;
}

void initPeerings (bool first) {
  // create internal peerings - CCU2 needs this
  if( first == true ) {
    HMID devid;
    sdev.getDeviceID(devid);
    for( uint8_t i=1; i<=sdev.channels(); ++i ) {
      Peer ipeer(devid,i);
      sdev.channel(i).peer(ipeer);
    }
  }
}

void initModelType () {
  uint8_t model[2];
  sdev.getDeviceModel(model);
  if( model[1] == 0x02 ) {
    sdev.channels(1);
    DPRINTLN(F("HM-LC-SW1-SM"));
  }
  else if( model[1] == 0x0a ) {
    sdev.channels(2);
    DPRINTLN(F("HM-LC-SW2-SM"));
  }
  else {
    DPRINTLN(F("HM-LC-SW4-SM"));
  }
}


void setup () {
  DINIT(57600,ASKSIN_PLUS_PLUS_IDENTIFIER);
  bool first = sdev.init(hal);
#ifdef HM_SENSOR_RELAY
  bool low = false;
#else
  bool low = (sdev.getConfigByte(CFG_LOWACTIVE_BYTE) == CFG_LOWACTIVE_ON) || checkLowActive();
#endif
  DPRINT("Invert ");low ? DPRINTLN("active") : DPRINTLN("disabled");
  sdev.channel(1).init(RELAY1_PIN,low);
  sdev.channel(2).init(RELAY2_PIN,low);
  sdev.channel(3).init(RELAY3_PIN,low);
  sdev.channel(4).init(RELAY4_PIN,low);

  buttonISR(cfgBtn,CONFIG_BUTTON_PIN);
#ifdef HM_SENSOR_RELAY
  buttonISR(btn1,BUTTON1_PIN);
  buttonISR(btn2,BUTTON2_PIN);
  buttonISR(btn3,BUTTON3_PIN);
  buttonISR(btn4,BUTTON4_PIN);
#endif
  initModelType();
  initPeerings(first);
  sdev.initDone();
}

void loop() {
  bool worked = hal.runready();
  bool poll = sdev.pollRadio();
  if( worked == false && poll == false ) {
    hal.activity.savePower<Idle<> >(hal);
  }
}

[jp112sdl]

I don't know the problem with IRSend... but I've seen that your serial has only 9 characters. It must be 10 characters fixed.

[pa-pa]

Which Pins are used by the IR ?